- Why is water dripping between gutter and fascia?
- What is the purpose of drip edge on a roof?
- How do you install drip edge flashing on an existing roof?
- Can you install drip edge over existing drip edge?
- How far should shingles extend past drip edge?
- Does gutter go over or under drip edge?
- Should drip edge be tight to fascia?
- Can you extend roof overhang?
- Do you need drip edge on gable ends?
- How do you bend a drip edge?
- Does roof sheathing go over fascia?
- How do I extend my drip edge?
- How much overhang should a roof have?
- Do all roofs need a drip edge?
- Do you need to replace drip edge when replacing roof?
- How do you extend a shingles overhang?
- Can you install drip edge after shingles?
- Does drip edge go over felt paper?
- What is the difference between drip edge and rake edge?
Why is water dripping between gutter and fascia?
Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter.
The gutter apron will prevent the dripping.
A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter..
What is the purpose of drip edge on a roof?
Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.
How do you install drip edge flashing on an existing roof?
Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.
Can you install drip edge over existing drip edge?
If the old drip edge is installed behind the gutter or the gutter is screwed through the drip edge and it cannot be removed without removing the gutter it is better to leave it there and install the new drip edge on Top. We do not remove and reinstall aluminum gutters.
How far should shingles extend past drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Does gutter go over or under drip edge?
If the overlap is too short, fix it by placing drip edge under the first row of roof shingles and be sure that the exterior edge is reaching over the gutter. If the gutter is lower than the bottom edge of the drip edge, install flashing behind the drip edge and over the back edge of the gutter to remove the gap.
Should drip edge be tight to fascia?
Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by …
Can you extend roof overhang?
Remove the facia board to expose the ends of the rafters. You can reuse this board if it is does not have any water damage / rot on it . Cut the overhang tail extensions out of new lumber and make them long enough to extend back to the house or into the house for a good secure attachment to the old rafters.
Do you need drip edge on gable ends?
What’s a drip edge? A drip edge is a piece of roofing trim. The drip edge supports overhanging shingles at the ends of a roof, providing structure to the overhang and directing water to the gutters and away from the fascia of the roof. … Drip edges can also be installed on the gable ends of a roof.
How do you bend a drip edge?
How to do it:Place the metal in the brake finished side down, leaving about 2-1/2 inches out of the brake.Bend a 90 degree corner.Remove the metal, spin it end for end and flip it over so that the brown side is up. … Insert the shorted leg into the break about 1’4 inch to bend a slight kick into the flashing.More items…•
Does roof sheathing go over fascia?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia.
How do I extend my drip edge?
If the gutter is mounted too far below the drip-edge, or if the kickout doesn’t extend far enough over the gutter, a retrofit solution would be to slip a strip of metal or rigid plastic flashing under the vertical fascia leg of the drip-edge and let the bottom edge of the strip overlap the back edge of the gutter.
How much overhang should a roof have?
The Longest Overhangs Two feet is the general maximum length for a typical roof overhang. This will protect a roof from most types of damage. Roof overhangs can extend farther than 2 feet, but beyond this length, they begin to lose structural integrity and require external supports.
Do all roofs need a drip edge?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Do you need to replace drip edge when replacing roof?
Drip Edge Flashing Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.
How do you extend a shingles overhang?
To fix an overhang that’s too short, buy some aluminum drip edge (aka drip-cap flashing). It’s typically sold in 8-ft. lengths, and can be cut with tin snips or even poultry shears. Slide the wide, flat flange of the flashing under the first course of shingles and adjust it to extend over the gutter.
Can you install drip edge after shingles?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Does drip edge go over felt paper?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
What is the difference between drip edge and rake edge?
Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.